Block Email

How to block email ???

• Login to yahoo for open your email;
• Clik Options Menu on the right your yahoo;
• Select email and click Block Address;
• So.. add email address into add block;
• Click OK if finish.

Beep Code

How to detect error with beep ?????

AST BIOS

• One short --> CPU register test failure
• Two short --> Keyboard controller buffer failure
• Three short --> Keyboard controller reset failure
• Four short --> Keyboard communication failure
• Five short --> Keyboard input failure
• Six short --> System board chipset failure
• Nine short --> BIOS ROM checksum error
• Ten short --> System timer test failure
• Eleven short --> ASIC failure
• Twelve short --> CMOS RAM shutdown register failure
• One long --> DMA controller 0 failure
• One long, one short --> DMA controller 1 failure
• One long, two short --> Video vertical retrace failure
• One long, three short --> Video memory test failure
• One long, four short --> Video adapter failure
• One long, five short --> 64KB memory failure
• One long, six short --> Unable to load interrupt vectors
• One long, seven short --> Unable to initialize video
• One long, eight short --> Video memory failure

IBM BIOS

• Two short --> Initialization error
• One long, one short --> System board error
• One long, two short --> Video adapter error
• One long, three short --> EGA/VGA adapter error
• Three long --> keyboard adapter error
• Continuous --> Power supply error
• No beep --> Power supply

Award Bios

• One long, two short --> Video adapter error
• Repeating (endless loop) --> Memory error
• One long, three short --> No video card or bad video RAM
• High frequency beeeps while running --> Overheated CPU
• Repeating High/Low --> Either the CPU is not seated properly or the CPU is damaged

Windows XP

How to upgrade from Microsoft Windows 98, Microsoft Windows Millennium Edition (Me), and Microsoft Windows 2000 Professional to Windows XP.

To upgrade to Windows XP:

• Start your computer, and then insert the Windows XP CD-ROM into the CD-ROM drive.If Windows automatically detects the CD-ROM, click Install Windows to start the Windows XP Setup Wizard.
• If Windows does not automatically detect the CD-ROM, click Start, click Run, type the following command, and then click OK: CD-ROM drive letter:\setup.exe
• When you are prompted to select an installation type, select Upgrade (the default setting), and then click Next.
• Follow the instructions on the screen to complete the upgrade.

Page Setup, Create Header/Footer and Printing (Office)

• Page Setup

This funtion is accomodate a document made of use the paper size.
To page setup, we can use :
- Click File menu;
- Click Page Setup.
Then step is paper size (A4, A3, etc..), margin (left margin, right margin, top margin, bottom), orientation (portrait or landscape) and lay out (header margin, footer margin, vertical alligment, different odd and even or different fist page, border page).
Step to continue is click OK if the finish

• Create header/footer and page number

For create header/footer and page number can be use :
- Click View menu;
- Click Header and Footer.
Step to continue is you can click insert auto text, insert page number, insert number of page, insert date, insert time, etc... and we can setup page number.

• File Printing

To print a file, we can use :
- Click File menu;
- Click Print.
Other way, we can use symbol on the toolbar menu.
Beside two methods, we can use button function, that fungtion is Ctrl –P.
From three methods, step to continue is select true printer, pages range to print, number of copies and next click OK if printer have ready.

I will critize and suggestion

Create, Save and Open File (Office)

How can I create, save and open file ??

• Create new file Can bu used by :

- Select File;
- Click New.
Other way, we can use symbol on the toolbar menu.
Beside two method of create new file, we can use function Ctrl-N.

• Save File

To save file, we can use by :
- Click File menu;
- Click Save.
Other way, we can use symbol on the toolbar menu.
Beside two methods, we can use button function, that function is Ctrl-S.

From three methods, if new documen have never been save so will be menu demand to give name.
We can giving a name, example : file1, and click Save button.

• Open FileTo open file, we can use :

- Click File menu;
- Click Open.

Other way, we can use symbol on the toolbar menu.
Beside two methods, we can use button function, that function is Ctrl-O.

From three methods, step to continue is select file name from directory and click Open button.

Thanks for your visited... i will critize and suggestion.

Network Card

How to install network card... ???

• Install a network card (if non on board);
• Turn on computer, wait… until active windows and open windows explore;
• Insert diskette drive or cd driver into drive or cd room;
• Click my computer;
• Double click disk drive or CD Room (otherwise…, double click Setup or Install);
• Wait…, double click network menu to install;

Note: if have been double click, the principle process is click Next.

Please to try and good luck.
<

Windows (1)

How to install windows without CD-Rom .... ?????

• Please install two hard disk (hard disk for installing and hard disk source program);
• Turn on computer;
• Wait … up to prompt A>, write E: or f: and press enter button;
• Change directory into source program, example: cd\master\win98 or cd\driver\win98;
• Write Setup or Install and press enter button;
• The same process, for next question .. please select Next up to finish, exception if you want different selection, please you modify.

Until install windows…, system may be not yet automatic detection any hardware.
So… we must install this hardware with compatible driver.
This processing is :

• Turn on computer, wait… up to windows menu and open windows explore;
• Insert CD Driver Motherboard;
• Click/select my computer;
• Double Click CD Rom (otherwise…, double click Setup or Install);
• Wait… until install menu, select menu for install hardware;

Note : if you has been double click, will continue menu choice and click Next.

Please to try and good luck.

Windows ()

How can I install windows with CD-Rom ???

• Insert Diskette DOS or if you will be booting with CD;
  
• Please setting bios so first booting from CD-Rom;
• Turn on computer;
• Next question…, will be using CD Room ?, Select/press 1 and press enter button;
• Wait …… up to prompt A>, write : E: and press Enter button (if hard disk is two partition, C and D)
• Write Setup or Install and press Enter button;
• For next question… select Next up to finish (please modify if you want different selection.

Please to try and good luck.

Formatting Hard Disk

• Insert Diskette DOS into Drive A;
• Turn on computer;
• Wait … up to prompt A>, please write : format c:/s (if you will be formatting disk C, and write : format d:, if you will be formatting disk d, etc..) and press Enter button;
• Select/press “Y” if exit question;
• Please wait………, up to ending process;
• If ending process, write label as your want, maximal 8 character;
• Next question, What do you want formatting anything ?, press “N” if you don’t want formatting anything and press “Y” if you want formatting anything hard disk;
• If you select “N”, so exit prompt A>;
  

We have to format a hard disk, please installation your system with Windows or etc….
please to try and good luck.

Setting Printer

How can I setting local printer ??

• Connect computer with printer;
• Click Start, Setting, Printer;
• Select Add Printer, and click Next;
• If type printer have been available in windows, select compatible Printer;
• But … type printer have not been available in windows, insert Driver Printer into Disk Drive or CD Room, than select Have Disk and system reading from Drive A or CD Room.
• Continue process… in principle than select/click Next;
• For windows ‘95/98 will be use Windows Driver, and system reading from directory windows driver, Example : d:\win98 or d:\driver\win98 or d:\master\win98.

Please to try and good luck.

Create Partition

How create partition ???

• Insert Diskette DOS into Drive A;
• Turn on computer;
• Wait… up to prompt A> please write : fdisk and press Enter button;
• Select and press key 1 (Create partition) then press Enter button;
• Select and press key 1 (Primary) then press Enter button;
• System will be detect hard disk’s capacity;
• Will be question, what hard disk will be capacuty used as all primary ? if you select “Y”, so all hard disk will be used as primary, but if you select “N” : (1) Will be exit capacity hard disk for primary, please edit with your requirement and press Enter button; (2) Select and press key 1 (Create partition) and press Enter button; (3) Select and press key 2 and press Enter button; (4) System will be detected capacity of hard disk unused and will be unused capacity hard disk, so press Enter button (if you want two partition);

• Wait … up to ending process;
• Press Esc/Escape button for exit to prompt A>;
• Turn off computer;
• Turn on computer;

We have to create partition’s……, please formatting your hard disk, please to try and good luck.

Bios Update

How can I BIOS Update (Basic Input/Output System Update) ???

• Turn On Computer;
• Pres key Del / Delete until exit bios program;
• Please editing menu bios like what you want.

Booting From CD-Rom ???

• You have set the FIRST BOOT device to CDROM in Advances BIOS Feature;
• Insert CD boot into CD-Rom;
• Restart your computer.
  

Booting From Floppy ???

• You have set the FIRST BOOT device to Floppy in Advances BIOS Feature;
• Insert DOS into Floppy;
• Restart your computer.
  

Please to try and good luck.